Drone view of completed fuel reduction around a fenced water reservoir
Wildfire Services

FireSmart & Fuel Reduction in BC

We do the machine and saw work behind FireSmart treatments: thinning, pruning, ladder fuel removal and debris cleanup around buildings, water infrastructure, towers and community edges. Based in 100 Mile House and working across BC.

The Work

What a FireSmart treatment involves

FireSmart treatment takes out the fuel that lets a fire reach a structure or climb into the crowns. On the ground that means removing ladder fuels, spacing the trees that stay, pruning them up off the ground, and cleaning up the dead and downed material underneath.

The machines do the heavy part. The excavator and track loader take out, move and deck the stems, pull stumps where the scope calls for it, and pile or load the debris. The CAT 305 and the John Deere 335P are both fully guarded for forestry work. The saw work around buildings, trails and fences is done by hand.

We work to the prescription or assessment you give us. If there isn't one yet, we walk the site with you and write the scope down before any work starts.

For burnt ground, danger trees and post-fire cleanup, see wildfire risk reduction and fire recovery.

Raked and cleaned-up ground after fuel reduction, with the excavator parked by the fence

On the job

Slash and stems piled along a reservoir fence part-way through fuel reduction
Crew member in full PPE feeding brush into a chipper during fuel reduction
Overhead drone view of a fuel-free zone cleared around a water reservoir in dense forest
Sunrise over 100 Mile House from a fuel reduction site, with the excavator and track loader parked
Standards

Working to the FireSmart zones

FireSmart BC measures the work out from the structure being protected. Treatment gets heavier the closer you get to it.

Immediate Zone — 0 to 1.5 m

Nothing that burns right against the structure. Vegetation, debris and combustibles come out down to a non-combustible surface.

Intermediate Zone — 1.5 to 10 m

Fuel is removed or tightly limited so a fire can't carry through to the structure. Conifers in this zone usually come out.

Extended Zone — 10 to 30 m

Thin conifers to at least 3 m between crowns, prune the remaining trees up to 2 m, and clean up branches, needles and dead material on the ground.

On critical infrastructure and larger properties the work often runs past 30 m to break up continuous fuel. We build that into the scope when the site needs it.

Clients

Who we do FireSmart work for

Municipalities and regional districts

Fuel removal around water towers, reservoirs, communication sites, parks and public buildings, and treatment along community edges. We work to your contract terms and keep the records funded programs ask for.

First Nations

Community fuel reduction and FireSmart work on the Nation's prescription and terms, with our own equipment and crew.

Utilities and site operators

Treatment around substations, towers, pump stations and lease sites. We can work inside an owner's site rules and safety program.

Ranches, resorts and large landowners

FireSmart treatment around homes, shops and yards on acreage, plus thinning further out where the property is big enough to need it.

How We Run It

From site walk to clean finish

  1. 01

    Site walk

    We walk the treatment area with you. Boundaries, trails, fences, utilities and anything that has to be protected get flagged.

  2. 02

    Written scope

    You get a written estimate with the treatment area, what comes out, what stays, how debris is handled and whether stumps are cut flush or pulled.

  3. 03

    The work

    Tree removal, thinning and pruning, then debris piled, chipped, loaded out or burned when burning is allowed. Any burn gets a 24-hour fire watch.

  4. 04

    Finish

    Site raked and cleaned up, trails reopened and the area photographed for your records.

FAQ

FireSmart work — straight answers

Do you do FireSmart assessments?

We aren't a FireSmart assessor. We do the treatment work once the assessment or prescription is done. If you don't have one yet, your local government's FireSmart program can usually arrange it, and we can walk the site with you to price the work.

What happens to the stumps?

Your choice, and it needs to be decided up front. Stumps can be cut flush to grade or pulled. Pulling them makes the cleanup faster. Raking clean around standing stumps is slow hand work, and the estimate reflects that.

How is the debris dealt with?

Piled and burned when the season and ventilation rules allow, chipped on site, or loaded out and hauled. Most jobs use a mix. It gets decided in the written scope, not on the day.

Can you work around trails, fences and buildings?

Yes. Trails and fence lines get flagged and protected before work starts, and trees close to structures are handled with the saw instead of the machine.

How far will you travel for FireSmart work?

We're based in 100 Mile House and take work across BC and into Alberta. See our page on province-wide mobilization.

What paperwork do you carry?

WorkSafeBC registered and in good standing, $5M commercial general liability through Northbridge, and a written safety management system with daily FLHAs and site emergency response plans. Documentation goes out on request.

Request a site assessment

  1. 1.Tell us about the ground — five minutes.
  2. 2.We walk it with you and talk through what's urgent, what can wait, and rough numbers.
  3. 3.You get a written estimate with a defined scope. If we're not the right fit, we'll say so and point you at who is.

Call or text 250-329-7356 to speak directly with the owner. Or send the project through the form and we'll respond within one business day.

WorkSafeBC registered · $5M CGL · Written SMS · S-100/S-185 crews

Call Text